防水防油整理劑AG-E 082

防水防油整理劑AG-E 082

AG-E 082賦予各種纖維以優異的防水防油特性:穩定性佳，受前道工序的殘留物染料及拼用助劑影響小:不屬于日本消防法的危險物，使用便利

一、物化性能             

外觀         淡黃色乳液

pH值         酸性

比重（20℃）  1.1

含固量     20%

離子性       弱陽離子

溶解性       易稀釋分散于水中                 

二、使用方法

AG - E082通常通過浸軋法加工使用。標準處方的使用濃度根據對象纖維材料、纖維以及使用目的而有所不同。一般情況下使用濃度為:

一般防水防油加工：AG- E082 20-60 g/L

耐久防水防油加工:

AG - E082 40-100 g/L，末端基封閉型異氰酸酯類交聯劑: 10-15g/L

干燥條件100-120℃ 1-3分鐘

烘焙條件: 150-170℃ 1~3分鐘

注意事項：

1.含氟加工劑通常具有加深顏色的效果。請提前確認好加工后的成品顏色。

2可以拼用抗靜電劑、柔軟劑、滲透劑等其他助劑,請事先充分確認其相容性及對防水防油性的影響

3.稀釋本品時請用40℃以下的水。加工中請將工作液溫度控制在40℃以下.

4.工作液的PH值請調節在7以下弱酸性，在強酸性和堿性的條件下會影響防水防油性能。

5.請盡早使用調配好的工作液.避免加工液的再使甩，

6.請將布料充分洗凈。盡量減少殘留的親水物或離子性物質，

7.由于樹脂渣易堆積在輥筒上.因此輥簡干燥不是理想的方法。

貯    存

1.在搬運本品時,請穿戴合適的個人防護裝備，不要將本品直接接觸身體。

2.不得吸入本品的蒸汽或霧氣。請避免氣化或霧化。

3.本產品請在5℃-35℃的范圍內貯存,避免陽光直射，密閉保存。在冷凍和長期高溫下保存，可能對品質產生不好的影響。

4.將本產品從容器中取出時，請先攪拌均勻。

5.本資料記載的內容僅提供對用戶有用的信息,并不作任何*。

Waterproof and Oil-proof

Finishing Agent

HOLPOSON? AG-E 082

AG-E 082 endows fibers with excellent water-proof and oil-proof properties.It has good stability and receives little influence from residual dyes and jointly-used auxiliaries in the previous process. It is not a dangerous substance under the Japanese Fire Service Law, and is convenient to use.

Physical & chemical properties:             

Appearance:           Pale yellow emulsion

pH value:               Acidic

Specific gravity (20 ℃): 1.1

Solid content:          20%

Ionicity:                Weak cationic

Solubility:              Easily dilutable and dispersable in water

Usage:

AG - E082 is usually used in padding treatment. The concentration in use as per the standard prescription varies according to the target fiber material, fiber and purpose of use. Generally, the concentrations used are:

General waterproof and oil proof processing: AG - E082 20-60g/L

Durable waterproof and oil proof processing: AG-E082 40-100g/L

End blocked isocyanate crosslinkers: 10-15g/L

Drying conditions

100-120 ℃ for 1-3 minutes

Baking conditions

150-170 ℃ for 1-3 minutes

Attentions:

1. Processing agents containing fluorine usually have the effect of deepening the color. Please confirm the color of finished products in advance.

2. Antistatic agents, softeners, penetrants and other auxiliaries can be used together. Please fully confirm their compatibilities and their influences on water and oil resistance in advance.

3. Please use water below 40 ℃ when diluting this product. Please control the working fluid’s temperature below 40 ℃ during processing

4. Please adjust the pH value of the working fluid below 7 in weak acidity, which will affect the waterproof and oil proof performance in strongly acidic and alkaline conditions.

5. Please use the prepared working fluid as early as possible to avoid further reusage of the processing fluid.

6. Please wash the fabric thoroughly to minimize residual hydrophilic or ionic substances.

7. Since resin slag is easy to accumulate on the roller, roller drying is not an ideal method.

Storage:

1. When carrying this product, please wear appropriate personal protective equipment and do not contact the body with the product directly.

2. Do not inhale the vapor or mist of this product. Please avoid vaporization or atomization.

3. Please store the product in the range of 5 ℃ - 35 ℃, avoid direct sunlight, and keep it in a closed place. It may have a bad effect on the quality to keep it in freeze or constant high temperature.

4. When taking the product out of the container, please mix it evenly first.

5. The contents recorded in this document only provide useful information for users without any guarantee.